android_device_qcom_common/rootdir/etc/init.qcom.sh

134 lines
3.9 KiB
Bash
Raw Normal View History

#!/system/bin/sh
# Copyright (c) 2009-2012, Code Aurora Forum. All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions are met:
# * Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# * Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in the
# documentation and/or other materials provided with the distribution.
# * Neither the name of Code Aurora nor
# the names of its contributors may be used to endorse or promote
# products derived from this software without specific prior written
# permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
# AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
# NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
# CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
# EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
#
target=`getprop ro.board.platform`
#
# Function to start sensors for DSPS enabled platforms
#
start_sensors()
{
mkdir -p /data/system/sensors
touch /data/system/sensors/settings
chmod 775 /data/system/sensors
chmod 664 /data/system/sensors/settings
mkdir -p /data/misc/sensors
chmod 775 /data/misc/sensors
if [ ! -s /data/system/sensors/settings ]; then
# If the settings file is empty, enable sensors HAL
# Otherwise leave the file with it's current contents
echo 1 > /data/system/sensors/settings
fi
start sensors
}
start_battery_monitor()
{
chown root.system /sys/module/pm8921_bms/parameters/*
chmod 0660 /sys/module/pm8921_bms/parameters/*
mkdir -p /data/bms
chown root.system /data/bms
chmod 0770 /data/bms
start battery_monitor
}
baseband=`getprop ro.baseband`
#
# Suppress default route installation during RA for IPV6; user space will take
# care of this
#
for file in /proc/sys/net/ipv6/conf/*
do
echo 0 > $file/accept_ra_defrtr
done
#
# Start gpsone_daemon for SVLTE Type I & II devices
#
case "$target" in
"msm7630_fusion")
start gpsone_daemon
esac
case "$baseband" in
"svlte2a")
start gpsone_daemon
start bridgemgrd
esac
case "$target" in
"msm7630_surf" | "msm8660" | "msm8960")
start quipc_igsn
esac
case "$target" in
"msm7630_surf" | "msm8660" | "msm8960")
start quipc_main
esac
case "$target" in
"msm8960")
start location_mq
start xtwifi_inet
start xtwifi_client
esac
case "$target" in
"msm7630_surf" | "msm7630_1x" | "msm7630_fusion")
value=`cat /sys/devices/system/soc/soc0/hw_platform`
case "$value" in
"Fluid")
start profiler_daemon;;
esac
;;
"msm8660" )
platformvalue=`cat /sys/devices/system/soc/soc0/hw_platform`
case "$platformvalue" in
"Fluid")
start_sensors
start profiler_daemon;;
esac
;;
"msm8960")
start_sensors
case "$baseband" in
"msm")
start_battery_monitor;;
esac
platformvalue=`cat /sys/devices/system/soc/soc0/hw_platform`
case "$platformvalue" in
"Fluid")
start profiler_daemon;;
"Liquid")
start profiler_daemon;;
esac
;;
esac